Helicoil Kits UNF

These VCOIL UNF Thread Repair Kits work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use a tang break tool or long nose pliers to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 1inchUNF x 12TPIDrill required but not supplied: 26mmInsert Tool Supplied: No23Inserts supplied per kit: 4 x 1.5 of the diameter in lengthDelivery 2 Days approx

A helicoil type 1.1/2UNF x 12TPI thread repair kit, with 1.5 x the diameter wire thread inserts.Supplied in a sturdy case.SpecificationsHex Taps: 2 x STI TapsInsert Tool with hex drive 10 x 1.1/2UNF x 12TPI x 1.5D Wire Thread InsertsDelivery 2 Days approxReplacement Inserts are Available

A helicoil type 1.1/4UNF x 12TPI thread repair kit, with 1.5 x the diameter wire thread inserts.Supplied in a sturdy case.SpecificationsHex Taps: 2 x STI TapsInsert Tool with hex drive 10 x 1.1/4UNF x 12TPI x 1.5D Wire Thread InsertsDelivery 2 Days approxReplacement Inserts are Available

A helicoil type 1.1/8UNF x 12TPI thread repair kit, with 1.5 x the diameter wire thread inserts.Supplied in a sturdy case.SpecificationsHex Taps: 2 x STI TapsInsert Tool with hex drive 10 x 1.1/8UNF x 12TPI x 1.5D Wire Thread InsertsDelivery 2 Days approxReplacement Inserts are Available

A helicoil type 1.3/8UNF x 12TPI thread repair kit, with 1.5 x the diameter wire thread inserts.Supplied in a sturdy case.SpecificationsHex Taps: 2 x STI TapsInsert Tool with hex drive 10 x 1.3/8UNF x 12TPI x 1.5D Wire Thread InsertsDelivery 2 Days approxReplacement Inserts are Available

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 1/2UNF x 20TPIDrill Supplied: 13mmInsert Tool Supplied: No15Tang Removal Tool Size: No15Inserts supplied per kit: 10 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 1/4UNF x 28TPIDrill Supplied: 6.7mmInsert Tool Supplied: No9Tang Removal Tool Size: No9Inserts supplied per kit: 20 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 3/16UNF x 32TPIDrill Supplied: 5.1mmInsert Tool Supplied: No8Tang Removal Tool Size: No8Inserts supplied per kit: 20 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL UNF Thread Repair Kits work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use a tang break tool or long nose pliers to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 3/4UNF x 16TPIDrill required but not supplied: 19.5mmInsert Tool Supplied: No21Inserts supplied per kit: 5 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 3/8UNF x 24TPIDrill Supplied: 9.8mmInsert Tool Supplied: No13Tang Removal Tool Size: No13Inserts supplied per kit: 15 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 5/16UNF x 24TPIDrill Supplied: 8.3mmInsert Tool Supplied: No11Tang Removal Tool Size: No11Inserts supplied per kit: 20 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL UNF Thread Repair Kits work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use a tang break tool or long nose pliers to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 5/8UNF x 18TPIDrill required but not supplied: 16.25mmInsert Tool Supplied: No18Inserts supplied per kit: 10 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL Complete UNF Thread Repair Kits come with everything you need and work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 7/16UNF x 20TPIDrill Supplied: 11.5mmInsert Tool Supplied: No14Tang Removal Tool Size: No14Inserts supplied per kit: 10 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL UNF Thread Repair Kits work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use a tang break tool or long nose pliers to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 7/8UNF x 14TPIDrill required but not supplied: 22.75mmInsert Tool Supplied: No22Inserts supplied per kit: 5 x 1.5 of the diameter in lengthDelivery 2 Days approx

These VCOIL UNF Thread Repair Kits work the same as Recoil and Helicoil kits. They are supplied with free running stainless steel wire thread inserts at 1.5 times the diameter in length and come in nice plastic cases to keep everything together Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use a tang break tool or long nose pliers to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Size: 9/16UNF x 18TPIDrill required but not supplied: 14.8mmInsert Tool Supplied: No16Inserts supplied per kit: 10 x 1.5 of the diameter in lengthDelivery 2 Days approx

This VCOIL Complete UNF Thread Repair Workshop Kit come with everything you need and work on the same principle as Recoil and Helicoil kits. They are supplied with Taps,Drills, Insert tools and Tang Removal tools and free running stainless steel wire thread inserts 1/4UNF - 1/2UNF Instructions for useClear the damaged thread with a standard drill or use a insert extractor.These VCOIL kits include the correct size drill to prepare for tapping up to M12 (1/2") Check that the thread and pitch of the tap and the bolt match. Use the special VCOIL Taps for cutting the holding thread into the cleared hole. Please use a suitable cutting oil. Place the insert onto the installation Tool and position the adjustable ring so that the insert tang is centred into the tang slot. Wind the insert in with a gentle downward pressure until a half turn below the surface. Do not work against the thread direction as the tang could snap. For the Tang removal lift the installation tool and use the tang break tool to remove the tang.Believe it or not, due to the narrow and exact tolerances the new thread normally is stronger than the original one.SpecificationsThread Sizes: 1/4 x 28tpi, 5/16 x 24tpi, 3/8 x 24tpi, 7/16 x 20tpi, 1/2 x 20tpiDrills Supplied: 6.7mm, 8.3mm, 9.8mm, 11.5mm, 13mmInsert Tools Supplied: No9, 11, 13, 14, 15Tang Removal Tools Size: No9, 11, 13, 14, 15Inserts supplied per kit: 95Delivery 2 Days approx